File Operations¶

In order to effect an operation on an individual file, the pathname and descriptor arguments passed to xfsctl identifies the file being operated on. The final argument described below refers to the final argument of xfsctl. All of the data structures and macros mentioned below are defined in the <xfs/xfs_fs.h> header file.

XFS_IOC_ALLOCSP
XFS_IOC_ALLOCSP64
XFS_IOC_FREESP

XFS_IOC_FREESP64

Alter storage space associated with a section of the ordinary file specified. The section is specified by a variable of type xfs_flock64_t, pointed to by the final argument. The data type xfs_flock64_t contains the following members: l_whence is 0, 1, or 2 to indicate that the relative offset l_start will be measured from the start of the file, the current position, or the end of the file, respectively (i.e., l_start is the offset from the position specified in l_whence). If the offset specified is before the current end of file, any data previously written into this section is no longer accessible. If the offset specified is beyond the current end of file, the file is grown and filled with zeroes. The l_len field is currently ignored, and should be set to zero.

XFS_IOC_ALLOCSP, XFS_IOC_ALLOCSP64, XFS_IOC_FREESP and XFS_IOC_FREESP64 operations are all identical.

These ioctls are no longer supported as of Linux 5.17.

XFS_IOC_FSSETDM

Set the di_dmevmask and di_dmstate fields in an XFS on-disk inode. The only legitimate values for these fields are those previously returned in the bs_dmevmask and bs_dmstate fields of the bulkstat structure. The data referred to by the final argument is a struct fsdmidata. This structure's members are fsd_dmevmask and fsd_dmstate. The di_dmevmask field is set to the value in fsd_dmevmask. The di_dmstate field is set to the value in fsd_dmstate. This command is restricted to root or to processes with device management capabilities. Its sole purpose is to allow backup and restore programs to restore the aforementioned critical on-disk inode fields. This ioctl is not supported as of Linux 5.5.

XFS_IOC_DIOINFO

Get information required to perform direct I/O on the specified file descriptor. Direct I/O is performed directly to and from a user's data buffer. Since the kernel's buffer cache is no longer between the two, the user's data buffer must conform to the same type of constraints as required for accessing a raw disk partition. The final argument points to a variable of type struct dioattr, which contains the following members: d_mem is the memory alignment requirement of the user's data buffer. d_miniosz specifies block size, minimum I/O request size, and I/O alignment. The size of all I/O requests must be a multiple of this amount and the value of the seek pointer at the time of the I/O request must also be an integer multiple of this amount. d_maxiosz is the maximum I/O request size which can be performed on the file descriptor. If an I/O request does not meet these constraints, the read(2) or write(2) will fail with EINVAL. All I/O requests are kept consistent with any data brought into the cache with an access through a non-direct I/O file descriptor.

XFS_IOC_FSGETXATTR
XFS_IOC_FSGETXATTRA

XFS_IOC_FSSETXATTR

See ioctl_xfs_fsgetxattr(2) for more information.

XFS_IOC_GETBMAP
XFS_IOC_GETBMAPA

XFS_IOC_GETBMAPX

See ioctl_getbmap(2) for more information.

XFS_IOC_RESVSP

XFS_IOC_RESVSP64

This command is used to allocate space to a file. A range of bytes is specified using a pointer to a variable of type xfs_flock64_t in the final argument. The blocks are allocated, but not zeroed, and the file size does not change. If the XFS filesystem is configured to flag unwritten file extents, performance will be negatively affected when writing to preallocated space, since extra filesystem transactions are required to convert extent flags on the range of the file written. If xfs_info(8) reports unwritten=1, then the filesystem was made to flag unwritten extents.

XFS_IOC_UNRESVSP

XFS_IOC_UNRESVSP64

This command is used to free space from a file. A range of bytes is specified using a pointer to a variable of type xfs_flock64_t in the final argument. Partial filesystem blocks are zeroed, and whole filesystem blocks are removed from the file. The file size does not change.

XFS_IOC_ZERO_RANGE

This command is used to convert a range of a file to zeros without issuing data IO. A range of bytes is specified using a pointer to a variable of type xfs_flock64_t in the final argument. Blocks are preallocated for regions that span holes in the file, and the entire range is converted to unwritten extents. This operation is a fast method of overwriting any from the range specified with zeros without removing any blocks or having to write zeros to disk. Any subsequent read in the given range will return zeros until new data is written. This functionality requires filesystems to support unwritten extents. If xfs_info(8) reports unwritten=1, then the filesystem was made to flag unwritten extents.

XFS_IOC_PATH_TO_HANDLE
XFS_IOC_PATH_TO_FSHANDLE
XFS_IOC_FD_TO_HANDLE
XFS_IOC_OPEN_BY_HANDLE
XFS_IOC_READLINK_BY_HANDLE
XFS_IOC_ATTR_LIST_BY_HANDLE
XFS_IOC_ATTR_MULTI_BY_HANDLE

XFS_IOC_FSSETDM_BY_HANDLE

These are all interfaces that are used to implement various libhandle functions (see open_by_handle(3)). They are all subject to change and should not be called directly by applications. XFS_IOC_FSSETDM_BY_HANDLE is not supported as of Linux 5.5.

Filesystem Operations¶

In order to effect one of the following operations, the pathname and descriptor arguments passed to xfsctl() can be any open file in the XFS filesystem in question.

XFS_IOC_FSINUMBERS

See ioctl_xfs_fsinumbers(2) for more information.

XFS_IOC_FSGEOMETRY

See ioctl_xfs_fsgeometry(2) for more information.

XFS_IOC_AG_GEOMETRY

See ioctl_xfs_ag_geometry(2) for more information.

XFS_IOC_FSBULKSTAT or XFS_IOC_FSBULKSTAT_SINGLE

See ioctl_xfs_fsbulkstat(2) for more information.

XFS_IOC_SCRUB_METADATA

See ioctl_xfs_scrub_metadata(2) for more information.

XFS_IOC_FSCOUNTS

See ioctl_xfs_fscounts(2) for more information.

XFS_IOC_GET_RESBLKS

XFS_IOC_SET_RESBLKS

See ioctl_xfs_getresblks(2) for more information. Save yourself a lot of frustration and avoid these ioctls.

XFS_IOC_GOINGDOWN

See ioctl_xfs_goingdown(2) for more information.

XFS_IOC_THAW
XFS_IOC_FREEZE
XFS_IOC_FSGROWFSDATA
XFS_IOC_FSGROWFSLOG

XFS_IOC_FSGROWFSRT

These interfaces are used to implement various filesystem internal operations on XFS filesystems. The remainder of these operations will not be described further as they are not of general use to applications.